DAQ 6062E DRIVER DOWNLOAD

If the vectors specified in these fields are shorter than the channel vector then the value of the last element in the vector will be used for the rest of the channels. In order to have analog outputs set to a particular voltage when the model is loaded or unloaded, the analog outputs must be configured on the HIL Initialize block’s Analog Outputs tab. This continues for the remaining channels. Please contact us to complete your request. Therefore, the acceptable value for duty cycle is related to the frequency at which the signal is being generated. One of our friendly Customer Service representatives will be contacting you shortly with information on when the equipment you requested will be available for viewing. Attempting to do so would produce an error message.

Uploader: Mikajas
Date Added: 4 October 2010
File Size: 34.80 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 15863
Price: Free* [*Free Regsitration Required]

If the vectors specified in these fields are shorter than the channel vector, the value of the last element in the vector will be used for the rest of the channels. Well, what if you were able to see a piece of equipment before you purchased it?

Ni Daqcard-6062e PCMCIA Multifunction DAQ National Instruments *tested*

It may be out of an acceptable range. Buying used equipment doesn’t always have to be a shot in the dark. Furthermore, a value of 0 for frequency is also not acceptable. Please feel free to contact us at sales artisantg. However, attempting to command a value which is out of range would not produce an error.

  ASUS P5Q TURBO ETHERNET DRIVER

When in duty 0662e mode, the acceptable range of duty cycles are:. The following are the available options and valid values for this board. Note that the PWM signal period is the frequency inverted.

DAQCard-6062

When adding a timebase block, you must change the Samples in buffer field or you will receive the error “The specified buffer size is not valid. Set the Analog output maximums and Analog output minimums fields matching the desired range of the analog outputs. Mercury Drive Champaign, IL Please contact one of our Customer Support Specialists if you have any questions about what is included with this equipment or if you require any additional information.

Then the ninth differential input’s positive line must be connected to channel 16, and negative line to channel Note that there are no spaces in the line. This continues for the remaining channels. Next set the analog input maximum and minimum.

Set the Analog output channels field to all the analog output channels that will be used on the board for the current diagram. All of the options follow the form:. One of our friendly Customer Service representatives will be contacting you shortly with information on when the equipment you requested will be available for viewing. Finally, set the Initial analog outputs and Final analog outputs to the desired voltage values.

For example, enter 4: You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment. Attempting to do so would produce an error message. Product price, specification, warranty and availability subject to change without notice.

  HITACHI DVD ROM GD S200 DRIVER

Hence, a scalar value will dxq to all channels specified in the Digital output channels field. The clocks can only be set indirectly with the functions that utilize them such as the timebase blocks.

National Instruments DAQCard E PCMCIA 12 Bit I O Card Ni DAQ | eBay

In order to set the encoder counters to a particular count when the model is loaded, the encoder inputs must be configured on the HIL Initialize block’s Encoder Inputs tab. Only one timebase block may be present in a diagram. As mentioned earlier in this section, the counters cannot be used as both encoder inputs and PWM outputs. Specify 1 to indicate channel 1 alone.

Not just a picture from the manufacturer’s website, but the actual piece of equipment you would receive. Also, the Set PWM output parameters at model start checkbox should always be vaq. Set the PWM output mode field to the desired output mode. Set the Encoder input channels field to all the encoder channels that will be used on the board for the current diagram.

The supported analog input configurations are Referenced singled-ended 0Non-referenced singled-ended 1Differential 2.